データシートサーチシステム
  Japanese  ▼
ALLDATASHEET.JP

X  

NRF52810-QFAA-R データシート(PDF) 253 Page - Nordic Semiconductor

部品番号 NRF52810-QFAA-R
部品情報  RF52810
PDF  483 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
メーカー  NORDIC [Nordic Semiconductor]
ホームページ  https://www.nordicsemi.com/
Logo NORDIC - Nordic Semiconductor

NRF52810-QFAA-R データシート(HTML) 253 Page - Nordic Semiconductor

Back Button NRF52810-QFAA-R Datasheet HTML 249Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 250Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 251Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 252Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 253Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 254Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 255Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 256Page - Nordic Semiconductor NRF52810-QFAA-R Datasheet HTML 257Page - Nordic Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 253 / 483 page
background image
Peripherals
register. This register value in conjunction with the selected PRESCALER of the PWM_CLK will result in a
given PWM period. A COUNTERTOP value smaller than the compare setting will result in a state where no
PWM edges are generated. Respectively, OUT[n] is held high, given that the polarity is set to FallingEdge.
All the compare registers are internal and can only be configured through the decoder presented later.
COUNTERTOP can be safely written at any time. It will get sampled following a START task. If
DECODER.LOAD is anything else than WaveForm, it will also get sampled following a STARTSEQ[n] task,
and when loading a new value from RAM during a sequence playback. If DECODER.LOAD=WaveForm, the
register value is ignored, and taken from RAM instead (see Decoder with EasyDMA on page 256 below).
PWM up counter example - FallingEdge polarity on page 254 shows the counter operating in up
(MODE=PWM_MODE_Up) mode with three PWM channels with the same frequency but different duty
cycle. The counter is automatically reset to zero when COUNTERTOP is reached and OUT[n] will invert.
OUT[n] is held low if the compare value is 0 and held high respectively if set to COUNTERTOP given that
the polarity is set to FallingEdge. Running in up counter mode will result in pulse widths that are edge-
aligned. See the code example below:
uint16_t pwm_seq[4] = {PWM_CH0_DUTY, PWM_CH1_DUTY, PWM_CH2_DUTY, PWM_CH3_DUTY};
NRF_PWM0->PSEL.OUT[0] = (first_pin << PWM_PSEL_OUT_PIN_Pos) |
(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->PSEL.OUT[1] = (second_pin << PWM_PSEL_OUT_PIN_Pos) |
(PWM_PSEL_OUT_CONNECT_Connected <<
PWM_PSEL_OUT_CONNECT_Pos);
NRF_PWM0->ENABLE
= (PWM_ENABLE_ENABLE_Enabled << PWM_ENABLE_ENABLE_Pos);
NRF_PWM0->MODE
= (PWM_MODE_UPDOWN_Up << PWM_MODE_UPDOWN_Pos);
NRF_PWM0->PRESCALER
= (PWM_PRESCALER_PRESCALER_DIV_1 <<
PWM_PRESCALER_PRESCALER_Pos);
NRF_PWM0->COUNTERTOP = (16000 << PWM_COUNTERTOP_COUNTERTOP_Pos); //1 msec
NRF_PWM0->LOOP
= (PWM_LOOP_CNT_Disabled << PWM_LOOP_CNT_Pos);
NRF_PWM0->DECODER
= (PWM_DECODER_LOAD_Individual << PWM_DECODER_LOAD_Pos) |
(PWM_DECODER_MODE_RefreshCount << PWM_DECODER_MODE_Pos);
NRF_PWM0->SEQ[0].PTR = ((uint32_t)(pwm_seq) << PWM_SEQ_PTR_PTR_Pos);
NRF_PWM0->SEQ[0].CNT = ((sizeof(pwm_seq) / sizeof(uint16_t)) <<
PWM_SEQ_CNT_CNT_Pos);
NRF_PWM0->SEQ[0].REFRESH = 0;
NRF_PWM0->SEQ[0].ENDDELAY = 0;
NRF_PWM0->TASKS_SEQSTART[0] = 1;
4430_161 v1.0
253



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


データシート ダウンロード

Go To PDF Page


リンク URL



ALLDATASHEETはお客様のビジネスに役立ちますか?  [ DONATE ] 

Alldatasheetは   |   広告   |   お問い合わせ   |   プライバシーポリシー   |   データシートへのリンク    |   リンク交換   |   メーカーリスト
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com