MCP3901A2T-ISLASHSS datasheet(21/60 Pages) MICROCHIP

21 / 60 page

DS22192A-page 21

MCP3901

4.8

Integral Non-Linearity Error

Integral non-linearity error is the maximum deviation of

an ADC transition point from the corresponding point of

an ideal transfer function, with the offset and gain

errors removed, or with the end points equal to zero.

It is the maximum remaining error after calibration of

offset and gain errors for a DC input signal.

4.9

Signal-To-Noise Ratio (SNR)

For the MCP3901 ADC, the signal-to-noise ratio is a

ratio of the output fundamental signal power to the

noise power (not including the harmonics of the signal),

when the input is a sinewave at a predetermined

frequency. It is measured in dB. Usually, only the

maximum signal to noise ratio is specified. The SNR

figure depends mainly on the OSR and DITHER

settings of the device.

EQUATION 4-4:

SIGNAL-TO-NOISE RATIO

4.10

Signal-To-Noise Ratio And

Distortion (SINAD)

The most important figure of merit for the analog

performance of the ADCs present on the MCP3901 is

the

Signal-to-Noise

And

Distortion

(SINAD)

specification.

Signal-to-noise and distortion ratio is similar to signal-

to-noise ratio, with the exception that you must include

the harmonics power in the noise power calculation.

The SINAD specification depends mainly on the OSR

and DITHER settings.

EQUATION 4-5:

SINAD EQUATION

The calculated combination of SNR and THD per the

following formula also yields SINAD:

EQUATION 4-6:

SINAD, THD, AND SNR

RELATIONSHIP

4.11

Total Harmonic Distortion (THD)

The total harmonic distortion is the ratio of the output

harmonics power to the fundamental signal power for a

sinewave input and is defined by the following

equation.

EQUATION 4-7:

The THD calculation includes the first 35 harmonics for

the MCP3901 specifications. The THD is usually only

measured with respect to the 10 first harmonics. THD

is sometimes expressed in%. For converting the THD

in %, here is the formula:

EQUATION 4-8:

This specification depends mainly on the DITHER set-

ting.

4.12

Spurious-Free Dynamic Range

(SFDR)

The ratio between the output power of the fundamental

and the highest spur in the frequency spectrum. The

spur frequency is not necessarily a harmonic of the

fundamental even though it is usually the case. This

figure represents the dynamic range of the ADC when

a full-scale signal is used at the input. This specification

depends mainly on the DITHER setting.

EQUATION 4-9:

SNR dB

()

SignalPower

NoisePower

----------------------------------

⎝⎠

⎛⎞

log

SINAD dB

()

SignalPower

Noise

HarmonicsPower

--------------------------------------------------------------------

⎝⎠

⎛⎞

log

SINAD dB

()

SNR

-----------

⎝⎠

⎛⎞

THD

–

----------------

⎝⎠

⎛⎞

log

THD dB

()

HarmonicsPower

FundamentalPower

-----------------------------------------------------

⎝⎠

⎛⎞

log

THD %

()

100

THD dB

()

------------------------

SFDR dB

()

FundamentalPower

HighestSpurPower

-----------------------------------------------------

⎝⎠

⎛⎞

log

MCP3901A2T-I/SS データシート(PDF) 21 Page - Microchip Technology

MCP3901A2T-I/SS データシート(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

データシートダウンロード