I. DC Electrical Characteristics (General - Applies to MCP6V06, MCP6V07 & MCP6V08 unless otherwise specified)

️· Supply Voltage: Not specified, but implied to be between 1.8V and 5.5V.
️· Common-Mode Input Voltage Range: Not specified, but implicitly related to the common-mode voltage referenced to VDD/3.
️· Input Bias Current: Not specified.
️· Input Offset Voltage: Not specified.
️· Input Offset Current: Not specified.
️· Output Leakage Current: Not specified.
️· Power Supply Current (per amplifier, no load): Not specified.
️· Output Short-Circuit Current: Not specified, but should be avoided.

II. AC Electrical Characteristics (Performance - Applies to MCP6V06, MCP6V07 & MCP6V08 unless otherwise specified)

️· Gain-Bandwidth Product (GBW): Not specified.
️· Slew Rate: Not specified.
️· Input Referred Noise Voltage: Not specified.
️· Intermodulation Distortion (IMD):
- VCM tone = 50 mVPKat 1 kHz, GN = 1
■ VDD = 1.8V: 32 µVPK
■ VDD = 5.5V: 25 µVPK
️· Start-up Time (tSTR): 500 µs (VOS within 50 µV of its final value)
️· Offset Correction Settling Time (tSTL): 300 µs (G = +1, VIN step of 2V, VOS within 50 µV of its final value)
️· Output Overdrive Recovery Time (tODR): 100 µs (G = -100, ±0.5V input overdrive to VDD/2)
️· Amplifier Output Leakage, CS High 20 pA

III. Digital/CS Interface (Specifically for MCP6V08)

️· CS Pull-Down Resistor (MCP6V08): 3-5 MΩ
️· CS Logic Threshold, Low (VIL): 0.3 VDD
️· CS Input Current, Low (ICSL): 5 pA
️· CS Logic Threshold, High (VIH): 0.7 VDD to VDD
️· CS Input Current, High (ICSH): Limited by the pull-down resistor value (VDD/RPD).
️· CS Input High, GND Current per amplifier (ISS):
- VDD = 1.8V: -0.7 µA
- VDD = 5.5V: -2.3 µA
️· Amplifier Output Leakage, CS High: 20 pA
️· CS Low to Amplifier Output On Turn-on Time (tON): 11-100 µs (CS Low = VSS+0.3 V, G = +1 V/V, VOUT = 0.9 VDD/2)
️· CS High to Amplifier Output High-Z Time (tOFF): 10 µs (CS High = VDD – 0.3 V, G = +1 V/V, VOUT = 0.1 VDD/2)

Key Differences / MCP6V08 Specifics:

️· The MCP6V08 includes a CS (Chip Select) pin for digital control of the amplifier output. The MCP6V06 and MCP6V07 do not.
️· The CS Interface section defines the voltage levels and current characteristics associated with the CS pin.
️· The CS interface timings (tON, tOFF) are relevant to the MCP6V08's controlled output behavior.



Important Notes:

️· Complete Datasheet: This is a summarized extraction. For proper design and operation, always refer to the complete MCP6V06/7/8 datasheet from Microchip's website. There are many more parameters and conditions not covered here.
️· Conditions: Many of these specifications are dependent on specific test conditions (temperature, supply voltage, load). The datasheet will detail these.
️· Typical vs. Maximum: Distinguish between typical values (what you can expect under common conditions) and maximum values (the absolute limits).