| データシートサーチシステム |
|
ADC32RF83 データシート(PDF) 49 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
ADC32RF83 データシート(HTML) 49 Page - Texas Instruments |
|
49 / 138 page ![]() THHH THHL BLKPKDET DWELL Time 49 ADC32RF80, ADC32RF83 www.ti.com SBAS774A – MAY 2016 – REVISED DECEMBER 2016 Product Folder Links: ADC32RF80 ADC32RF83 Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated Figure 126. Peak Power Detector Timing Diagram Table 9 shows the register configurations required to set up the absolute peak power detector. The detector operates in the fS / 8 clock domain; one peak sample is calculated over eight actual samples. The automatic gain control (AGC) modes can be configured separately for channel A (54xxh) and channel B (5Cxxh), although some registers are common in 54xxh (such as the GPIO pin selection). Table 9. Registers Required for the Peak Power Detector REGISTER ADDRESS DESCRIPTION PKDET EN 5400, 5C00h Enables peak detector BLKPKDET 5401h, 5402h, 5403h, 5C01h, 5C02h, 5C03h Sets the block length N of number of samples (S`). Number of actual ADC samples is 8X this value: N is 17 bits: 1 to 216. BLKTHHH, BLKTHHL, BLKTHLH, BLKTHLL 5407h, 5408h, 5409h, 540Ah, 5C07h, 5C08h, 5C09h, 5C0Ah Sets the different thresholds for the hysteresis function values from 0 to 256 (where 256 is equivalent to the peak amplitude). For example: if BLKTHHH is to –2 dBFS from peak, 10(–2 / 20) × 256 = 203, then set 5407h and 5C07h = CBh. DWELL 540Bh, 540Ch, 5C0Bh, 5C0Ch When the computed block peak crosses the upper thresholds BLKTHHH or BLKTHLH, the peak detector output flags are set. In order to be reset, the computed block peak must remain continuously lower than the lower threshold (BLKTHHL or BLKTHLL) for the period specified by the DWELL value. This threshold is 16 bits and is specified in terms of fS / 8 clock cycles. OUTSEL GPIO[4:1] 5432h, 5433h, 5434h, 5435h Connects the BLKPKDETH, BLKPKDETL alarms to the GPIO pins; common register. IODIR 5437h Selects the direction for the four GPIO pins; common register. RESET AGC 542Bh, 5C2Bh After configuration, reset the AGC module to start operation. |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |