| データシートサーチシステム |
|
ADC32RF83 データシート(PDF) 67 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
ADC32RF83 データシート(HTML) 67 Page - Texas Instruments |
|
67 / 138 page ![]() R/W A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 Register Address [7:0] Register Data [7:0] SDIN SCLK SEN RESET A11 A10 A9 A8 A7 A6 M P CH 0 1 0 1 0/1 0/1 0 0 R/W A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 Register Address [11:0] Register Data [7:0] = XX SDIN SCLK SEN RESET A11 A10 A9 A8 A7 A6 M P CH 1 1 1 0 D7 D6 D5 D4 D3 D2 D1 D0 SDOUT SDOUT [7:0] 67 ADC32RF80, ADC32RF83 www.ti.com SBAS774A – MAY 2016 – REVISED DECEMBER 2016 Product Folder Links: ADC32RF80 ADC32RF83 Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated 8.4.3.4 Serial Register Readout: Digital Bank Readback of the register in one of the digital banks (as shown in Figure 141) can be accomplished by: 1. Driving the SEN pin low. 2. Selecting the page in the digital page: follow step 2 in the Serial Register Write: Digital Bank section. 3. Set the R/W, M, and P bits to 1, select channel A or channel B, and write the address to be read back. – JESD digital page: use the CH bit to select channel B (CH = 0) or channel A (CH = 1). 4. Read back the register content on the SDOUT pin. When a page is selected, multiple read backs from the same page can be done. Figure 141. SPI Read Timing Diagram for the Digital Bank 8.4.3.5 Serial Register Write: Decimation Filter and Power Detector Pages The decimation filter and power detector pages are special pages that accept direct addressing. The sampling clock and SYSREF signal are required to properly configure the decimation settings. Registers located in these pages can be programmed in one SPI cycle (Figure 142). 1. Drive the SEN pin low. 2. Directly write to the decimation filter or power detector pages. To program registers in these pages, set M = 1 and CH = 1. Additionally, address bit A[10] selects the decimation filter page (A[10] = 0) or the power detector page (A[10] = 1). Address bit A[11] selects channel A (A[11] = 0) or channel B (A[11] = 1). – Decimation filter page: write address 50xxh for channel A or 58xxh for channel B. – Power detector page: write address 54xxh for channel A or 5Cxxh for channel B. Example: Writing address 5001h with 02h selects the decimation filter page for channel A and programs decimation factor of divide-by-8 (complex output). Figure 142. SPI Write Timing Diagram for the Decimation and Power Detector Pages |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |