| データシートサーチシステム |
|
PC87309VLJ データシート(PDF) 66 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
PC87309VLJ データシート(HTML) 66 Page - National Semiconductor (TI) |
|
66 / 192 page ![]() The Floppy Disk Controller (FDC) (Logical Device 0) 66 www.national.com Result Phase Upon terminating the execution phase of the READ DATA command, the controller asserts IRQ6, indicating the begin- ning of the result phase. The microprocessor must then read the result bytes from the FIFO. The values that are read back in the result bytes are shown in TABLE 3-17 on page 66. If an error occurs, the result bytes indicate the sector read when the error occurred. 3.7.11 The READ DELETED DATA Command The READ DELETED DATA command reads logical sec- tors containing a Address Mark (AM) for deleted data from the selected drive and makes the data available to the host microprocessor. This command is like the READ DATA command, except for the setting of the Control Mark bit (bit 6) in ST2 and the skipping of sectors. See description of execution phase. See READ DATA command for a description of the command bytes. Command Phase Execution Phase Data read from disk drive is transferred to the system in DMA or non-DMA modes. See Section 3.4.2 on page 45. See TABLE 3-17 on page 66 for the state of the result bytes when the command terminates normally. The effect of Skip Control (SK) on the READ DELETED DATA command is summarized in TABLE 3-18 on page 67. TABLE 3-17. Result Phase Termination Values with No Error 1. End of Track sector number from the command phase. 2. The number of the sector last operated on by controller. 3. Track number programmed in the command phase 76543210 Result Phase Status Register 0 (ST0) Result Phase Status Register 1 (ST1) Result Phase Status Register 2 (ST2) Track Number Head Number Sector Number Bytes-Per-Sector Code 76543210 MT MFM SK 01100 IPS XXXX HD DS1 DS0 Track Number Head Number Sector Number Bytes-Per-Sector Code End of Track (EOT) Sector Number Bytes Between Sectors - Gap 3 Data Length (Obsolete) Multi-Track (MT) Head # (HD) End of Track (EOT) Sector Number ID Information in Result Phase Track Number Head Number Sector Number Bytes-per-Sector Code 0 0 < EOT1 Sector # No Change No Change Sector2 # + 1 No Change 00 = EOT1 Sector # Track3 # + 1 No Change 1 No Change 01 < EOT1 Sector # No Change No Change Sector2 # + 1 No Change 01 = EOT1 Sector # Track3 # + 1 No Change 1 No Change 10 < EOT1 Sector # No Change No Change Sector2 # + 1 No Change 10 = EOT1 Sector # No Change 1 1 No Change 11 < EOT1 Sector # No Change No Change Sector2 # + 1 No Change 11 = EOT1 Sector # Track3 # + 1 0 1 No Change |
|
リンク URL |
| ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | データシートへのリンク | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |